Update Cisco CCNP 300-135 TSHOOT exam test answers

It is worth spending a little money to get so much results. Our Passtcert Cisco CCNP 300-135 TSHOOT exam test answers can not only give you a good exam preparation, allowing you to pass Cisco certification 300-135 exam, but also provide you with one-year free update service.If you want to choose passing Cisco certification 300-135 exam to make yourself have a more stable position in today's competitive IT area and the professional ability become more powerful, you must have a strong expertise. And passing CCNP certification 300-135 exam is not very simple.

Share some CCNP 300-135 exam questions and answers below.
The fault condition is related to which technology? 
A. NTP 
B. IP DHCP Server 
C. IPv4 OSPF Routing 
D. IPv4 EIGRP Routing 
E. IPv4 Route Redistribution 
F. IPv6 RIP Routing 
G. IPv6 OSPF Routing 
H. IPV4 and IPV6 Interoperability 
I. IPv4 layer 3 security 
Answer: G

What is the solution to the fault condition? 
A. Under the interface Tunnel34 configuration enter the ipv6 ospf 6 area 34 command. 
B. Under the interface Loopback6 configuration enter the ipv6 ospf 6 area 34 command. 
C. Under the interface Serial0/0/0.34 configuration enter the ipv6 ospf 6 area 34 command. 
D. Under ipv6 router ospf 6 configuration enter the redistribute rip RIP_ZONE include-connected command. 
Answer: D

What is the solution of the fault condition? 
A. Under the BGP process,enter the bgp redistribute-internal command 
B. Under the BGP process, bgp confederation identifier 65001 command 
C. Delete the current BGP process and reenter all of the commands using 65002 as theAS number. 
D. Under the BGP process, delete the neighbor 209.56.200.226 remote-as 65002 command enter the neighbor 209.65.200.226 remote-as 65002 command. 
Answer: D 

R1 and R2 OSPF neighbor. 
Which two statements are true? (Choose two) 
(Output from show ip ospf neighbors on 2 routers, one of them shows FULL/DR, the other FULL/-, you need to know how were they configured and will they exchange routes) 
A. They are not neighbors 
B. R1 (non-DR) will not update its routes to R2 
C. Router R2 is configured with ospf point-to-point command (R2 is the router that shows as FULL/-) 
D. They need to be configured as OSPF NBMA 
E. R2 should be configured as stub 
Answer: BC

Two routers are connected through PPP connection. After the PPP was established the admin put OSPF running above it. The OSPF formed adjacency but after soon the adjacency dropped. 
What is the reason? (The cause of OSPF forming an adjacency over a GRE tunnel and dropping immediately) 
A. MTU does not match 
B. Area 0 need to exist for OSPF to function properly 
C. Gre tunnel destination is not reachable through tunnel 
D. Gre tunnel ip address must be covered by network under ¡°router ospf 1¡± 
E. ospf routes contains the route to tunnel destination 
Answer: C

The Fault Condition is related to which technology? 
A. BGP 
B. NAT 
C. IP NAT 
D. IPv4 OSPF Routing 
E. IPv4 OSPF Redistribution 
F. IPv6 OSPF Routing 
G. IPv4 layer 3 security 
Answer: G

What is the MTU¡¯s size in a GRE tunnel? 
A. 1630 
B. 1476 
C. 1500 
D. 1900 
Answer: B

What is the solution of the fault condition? 
A. Under the interface Serial0/0/0 configuration enter the ip nat inside command 
B. Under the interface Serial0/0/1 configuration enter the ip nat outside command 
C. Under the ip access-list standar nat_trafic configuration enter the permit 10.2.0.0 0.0.255.255 command 
D. Under the ip access-list standar nat_trafic configuration enter the permit 209.65.200.0 0.0.0.255 command 
Answer: C 


What is the solution of the fault condition? 
A. Under the ip access-list edge_security configuration add the permit ip 209.65.200.224 0.0.0.3 any command 
B. Under the interface Serial0/0/1 enter the ip access-group edge_security out command. 
C. Under the ip access-list edge_security configuration delete the deny ip 10.0.0.0 0.255.255.255 any command 
D. Under the interface Serial0/0/0 configuration delete the ip access-group edge_security in command and enter the ip access group edge_security out command 
Answer: A

To encounter Passtcert, you will encounter the best training materials. You can rest assured that using our Cisco CCNP 300-135 TSHOOT exam test answers. With it, you have done fully prepared to meet this exam. Add Passtcert products to cart now! You will have 100% confidence to participate in the exam and disposably pass Cisco certification 300-135 exam. At last, you will not regret your choice.Now there are many IT professionals in the world and the competition of IT industry is very fierce.

With Passtcert Cisco CCNP 300-135 TSHOOT exam test answers, you can get what you want.The Cisco 300-135 certification exam is not only validate your skills but also prove your expertise. It can prove to your boss that he did not hire you in vain. The current IT industry needs a reliable source of Cisco 300-135 certification exam, Passtcert is a good choice. Select Passtcert Cisco CCNP 300-135 TSHOOT exam test answers, so that you do not need yo waste your money and effort. And it will also allow you to have a better future.

Related article: http://updated-exam.blogspot.com/2017/09/update-cisco-certification-300-135.html